Just How to Replace a Tub
Just How to Replace a Tub
Blog Article
Each person has got his or her own notions in relation to Installing A Bathtub.
Setting up a bathtub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a moderately difficult task. If the old tub is conveniently easily accessible, the project can relocate rapidly; if you have to open up a wall to get rid of the old tub and also position the new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will require a helper to vacate the old tub and embeded in the new one. Make certain you have certified yourself for the work and fit attempting it. As opposed to hiring a service provider to take over a halfway-completed task, it is better to take into consideration employing one prior to you start. Possibilities are you might need an expert plumber to make tube connections.
This post will certainly assist you mount a new tub in your bathroom if you have currently acquired a new bathtub and do not need to alter the arrangement of your previous water system pipes.
Your devices and product list ought to consist of the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The procedure of removing the existing taps can be fairly problematic because of the limited access that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a cloth all set for the continuing to be water that will originate from the pipelines. When the supply pipelines have been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will require lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin making certain that the washing machines remain in area in between the faucet as well as the sink. Protect the tap in place with the manufacturer provided backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous kind must be linked to the tap ends first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bathtub
Using both wood boards under its feet, put the bathtub in the needed position. The wood boards are handy in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the tub until the level checks out level.
To mount taps, fit the bottom of the outermost flexible faucet port to the suitable supply pipeline by making a compression sign up with; then do the very same for the other tap.
Turn on the supply of water and also inspect all joints and brand-new pipework for leaks and also tighten them if required. Fill the tub and additionally check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Lastly, fix the bathroom paneling as described in the maker's instruction manual. Tiling and also securing around the bathtub needs to wait until the tub has been utilized at least once as this will certainly settle it right into its final placement.
Preparing for the Setup
Firstly, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the faucet features a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to prevent stress on the bath tub.
Fit the flexible tap adapters to the bottom of both taps utilizing 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last placement.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to crack a rigid seal, triggering the water to permeate the wall between the bathroom as well as the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components as well as fittings. They are sold in tubes and cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can break fairly early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were guided to that report on Installing A Bathtub from an acquaintance on another web property. Are you aware of someone else who is occupied with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Take a moment to share it. Thanks a bunch for your time. Come back soon.
Book Maintenance Report this page